Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
Here in the next paragraph you will find some sound insight regarding A Step-by-Step Guide to Installing a Bathtub.
Setting up a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably difficult task. If the old tub is conveniently easily accessible, the job can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will need a helper to leave the old tub and also set in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already gotten a brand-new tub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools and product checklist must consist of the following:
Planning for the Installment
To start with, the supporting framework supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited accessibility that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. Once the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the required placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the level checks out level.
To mount faucets, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipe by making a compression join; then do the same for the various other tap.
Turn on the water system as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill the bath tub and likewise check the overflow outlet and also the typical outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the tub has been utilized at least when as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers are in location between the tap and also the sink. Safeguard the tap in position with the maker provided backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall between the bathroom and the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that segment was really helpful. If you please take a moment to share this blog posting if you enjoyed it. Many thanks for your time. Don't forget to visit our blog back soon.
Prices & Booking Report this page